CIMCO Catalog_2017_18

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 293 Design PU Article no. Design PU Article no. Advice and ordering: Phone: +49 (0)2191 3718-01, Fax: +49 (0)2191 3718-85, E-mail: order@cimco.de Heat-shrink tubes Made from homogenous polyolefin, thermally stabilised, cross-linked by irradiation, with outstanding mechanical stability, chemical resistance and electrical properties: Significant mechanical performance properties (typical measured values): Tensile strength 14.8 MPa / min (N/mm2 ), tensile strength after heat ageing 14.5 MPa / min (N/mm2 ), elongation at break 460%, elongation at break after heat ageing (168 h at +158 °C) 480%, thermal shock (4 h at +250 °C) 8% with complete shrinkage, cold shock (1 h at –30 °C) no breaking. Continuous operation temperature -55 °C to +125 °C. Very good printability with heat seal-, inkjet- and offset printing. Significant chemical performance properties: Excellent UV light, ozone and salt water resistance, good resistance to commonly used chemicals (cleaners and solvents, weak acids and bases, fuels, oils), resistance to fungus and rot (Rating 1 according to ISO 846 Method A). The heat shrink tubes do not contain any asbestos, azoic compounds, formaldehydes or silicone. The heat shrink tubes are self-extinguishing according to UL 224 VW-1. No dioxin is released during incineration. The products are non-corrosive (compatible with copper) and compatible with all commonly used materials for cable insulation, such as plastic, rubber, lead, steel, aluminium, silicone, etc. Significant electrical performance properties: Dielectric strength 17 kV/mm (green-yellow design 15 kV/mm), specific electrical resistance 1 x 1015 Ω/cm (yellow-green design 1 x 1014 Ω/cm), Further detailed mechanical, chemical and electrical product data, as well as an overview of the approvals and certifications from various test institutes, can be obtained on request in the form of our Technical Data Sheets. Detailed dimensions of the individual types and sizes of the CIMCO heat shrink tube range can be found on page 299. Working instructions: • If necessary, cut the heat shrink tube to the desired length, taking care to ensure a smooth cut edge. • Only undertake shrinking on clean surfaces, as free of dust and grease as possible. • Begin the shrinking process, starting at one end of the tube. • Shrinking temperature from +70 °C to +115 °C. • Ideally, work with a special hot-air blower, heating furnace or infrared lamp. Thin-walled, black heat shrink tube, shrinkage ratio 2 : 1 Halogen-free, thin-walled, flexible standard electrical heat shrink tube with shrinkage ratio 2 : 1 (shrinking capability down to half the specified internal diameter before heat shrinking). Highly suitable for electrical insulation, as bend- and abrasion protection, as damp protection for seals, for bundling, for strain relief and for marking in electronics and electrical engineering, telecommunications, cable assembly, in the automotive industry and many other areas Supplied on dispenser rolls, stable, environmentally friendly cardboard rolls, diameter approx. 300 mm - 550 mm (depending on size of heat shrink tube), core diameter approx. 30 mm, for industrial use in particular. Nominal-ø BEFORE shrinking Shrink range Length inch mm mm m  3/64   1.1 0.5  - 11.0 200 1 Roll 18 4002  1/16   1.5 0.65 - 1.5 200 1 Roll 18 4004  3/32   2.5 1.0  - 2.5 200 1 Roll 18 4006  1/8   3.5 1.5  - 3.5 200 1 Roll 18 4008  3/16   5.0 2.3  - 5.0 100 1 Roll 18 4010  1/4   6.5 3.0  - 6.5 100 1 Roll 18 4012  3/8   9.5 4.5  - 9.5 100 1 Roll 18 4014   1/2   12.5 6.0   - 12.5 100 1 Roll 18 4016   3/4   19.0 9.0   - 19.0 100 1 Roll 18 4018 1   26.0 12.5   - 26.0 50 1 Roll 18 4020 1 1/2   41.5 20.0   - 41.5 50 1 Roll 18 4022 2   50.0 25.0   - 50.0 25 1 Roll 18 4024 3   80.0 41.0   - 80.0 25 1 Roll 18 4026 4 100.0 51.0   - 100.0 25 1 Roll 18 4028 Advice and ordering: Phone: +49 (0)21913718-01, Fax: +49 (0)21913718-85, E-mail: order@cimco.de  3/64   1.10.5  - 11.02001 Roll 184002  1/16   1.50.65 - 1.52001 Roll 184004  3/32   2.51.0  - 2.52001 Roll 184006  1/8   3.51.5  - 3.52001 Roll 184008  3/16   5.02.3  - 5.01001 Roll 184010  1/4   6.53.0  - 6.51001 Roll 184012  3/8   9.54.5  - 9.51001 Roll 184014   1/2   12.56.0   - 12.51001 Roll 184016   3/4   19.09.0   - 19.01001 Roll 184018 1   26.012.5   - 26.0501 Roll 184020 11/2   41.520.0   - 41.5501 Roll 184022 2   50.025.0   - 50.0251 Roll 184024 3   80.041.0   - 80.0251 Roll 184026 4100.051.0   - 100.0251 Roll 184028

Seitenübersicht